Author Topic: HDDHackr v1.40 Build 20130303  (Read 695041 times)

juggernault

  • Newbie
  • *
  • Posts: 5
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #220 on: October 31, 2009, 01:02:11 AM »
Hi people,

1.JamakinJoel : the undo.bin wont work for me, appears i need same model... but thx
2.All: If i try a brute flash in my WD2500BEVS 26UST0 (modded to 120GB) i receive a message"Sectors 16-22 rewwritten successfully!"(green)
and "Can't save drive firmware for later restore!" (red). And nothing happens. What ido?

Thx

jelle2503

  • Xbox Hacker
  • *****
  • Posts: 1686
  • elitist prick
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #221 on: October 31, 2009, 02:49:06 AM »
i flashed 5 WD2500BEVT succesfully on Nvidia Nforce 2 Ultra.. no need for power off PC I just ctrl+c hddhackr after it's done then take the next
*

juggernault

  • Newbie
  • *
  • Posts: 5
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #222 on: October 31, 2009, 09:29:21 AM »
So what's going on?

kartaq

  • Member
  • **
  • Posts: 14
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #223 on: November 01, 2009, 08:11:15 PM »
I have a question:

My mainboard does cause the known HPA problem (2MB Hidden Partition at the end of the drive). Knowing this,
I left my drive unpowered during post and flashed it with an unaltered LBA and let HDDHACKR create the 3 Partitions.

However I was absent-minded and rebootet my machine and sure enough the drive had the HPA set and it
ruined Xbox compatibility in the process. I quickly removed the HPA using MHDD and the drive is working fine with my console so far.
Now I'd like to know, if the 3rd Partition (the largest) spans all the way to the end of the Harddisk and if my Mainboard
could possibly have shrunk it when it created the HPA, and if I should go through the trouble of re-doing the whole process
for the sake of security ..?

unix

  • Newbie
  • *
  • Posts: 2
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #224 on: November 02, 2009, 03:02:43 PM »
I am trying to flash a 250gb hdss.bin file
My hard drive is a WD2500BEVS  (june 08)
I boot from usb and the drive is detected on my sata card (e800).
I select flash
A warning about not the same do I want to put a compatible xbox version. I select yes. Do i want to create partitions. I select yes.

Then it goes this far:

Sectors 16-22 rewritten successfully!
Preparing [                ] 0%
Can't create partitions!iled!


I have tried undo and then retry but its the same error I get stuck on.

1 time when it got to the Preparing part it hit 1%, then threw me out with same error Can't create partitions!iled!

Uptate:
Just tried manuallly create partitions using the command
HDDHACKR C e800 a0
It went to 1% and then returned the error - Preparing partition 3 failed!

Any help appreciated...



« Last Edit: November 02, 2009, 03:26:22 PM by unix »

davij086

  • Newbie
  • *
  • Posts: 2
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #225 on: November 02, 2009, 04:35:37 PM »
Hello, Just wondering this Western Digital Brute Force, It seems to keep coming back as either 0x10 or 0x90 what does this mean? and if so is the drive recoverable?

atikosh

  • Newbie
  • *
  • Posts: 7
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #226 on: November 02, 2009, 04:41:29 PM »
Hi

I flash a 250gb wd2500BEVT (wd scorpio blue) with 250GB hdss.bin
It works on my falcon board but when i use my jasper board it gives me an 68 error code. Any idea will helpfull.

Thanks in advance

driver

  • Newbie
  • *
  • Posts: 1
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #227 on: November 03, 2009, 08:49:24 AM »
Hi all

Can anyone upload firmware for WD1200BEVS-75LAT0, because I f*** up my hdd and I need firmware.
Firmware Rev: 02.06M02

10x !!!

Malvadojedi

  • Newbie
  • *
  • Posts: 1
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #228 on: November 04, 2009, 07:53:17 AM »
Hi just to say thanks for this programme worked a treat.  Can confirm that managed to do a 320GB BEVT -00ZAT0 HDD DDHackr v1.22.  Only really thing that puzzled me was after flashing the hdd and creating the partitions and rebooting everything and tried to flash again to confirm compatability the message on screen said that the info in the HDDSS.BIN didn't match the info on the hdd which on screen it did, anyway I ignored this cause I could see that on screen I could see that the info was exactly the same, model nš., serial etc.  The only thing I can think of was that the HDDSS.BIN I used was from a Hitachi hdd instead of a Fujitsu hdd?  Also some where earlier on this thread I think I read something about microsoft using only Fujitsu hdd's?  Well both my 20GB aren't, one's a Hitachi and the other is a Samsung.

Again thanks for HDDHackr

Regards Frank

roachparty

  • Newbie
  • *
  • Posts: 2
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #229 on: November 04, 2009, 01:29:08 PM »
hddhackr v1.22 is not reading my drive.  it is running from dos 6.21 booted from an sd card, hddhackr loads and says no ATA devices are found  HELP!!

drive type is western digital WD1200BEVS 120Gb
« Last Edit: November 04, 2009, 01:36:21 PM by roachparty »

dreamcloud

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #230 on: November 04, 2009, 05:43:00 PM »
Hi, i got a problem....

i flashed my WD50000BEVT using hddhackr v1.22 with 250gb hddss.bin
it work and able to detect on my xbox360... but when everytime power on my xbox it will have E68 error... so wat i did is unplug the hdmi and plug it back...

is there anyway to fix this issue? thank ;p

dreamcloud

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #231 on: November 04, 2009, 05:49:02 PM »
oh 1 more question... if i have Fujitsu MHW2120BH same model which xbox is using... is it possible to make it to xbox hdd?

thank~

damox

  • Master Hacker
  • ****
  • Posts: 485
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #232 on: November 04, 2009, 11:43:52 PM »
oh 1 more question... if i have Fujitsu MHW2120BH same model which xbox is using... is it possible to make it to xbox hdd?

thank~

No, only WD drives are supported by hddhackr.

dreamcloud

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #233 on: November 05, 2009, 12:19:57 AM »
oh 1 more question... if i have Fujitsu MHW2120BH same model which xbox is using... is it possible to make it to xbox hdd?

thank~

No, only WD drives are supported by hddhackr.


thanks damox.... how about the e68 error ; ;

Arakon

  • Administrator
  • Xbox Hacker
  • *****
  • Posts: 6925
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #234 on: November 05, 2009, 02:19:17 PM »
E68 is usually a defective drive, or a drive that is starting up too slowly so it times out.
I do NOT give support by email, PM, ICQ or whatever. Anyone annoying me that way will have his balls removed. With a rusty butterknife. Slowly. And I'll enjoy doing it.

Hatenko

  • Newbie
  • *
  • Posts: 2
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #235 on: November 05, 2009, 02:57:40 PM »
I'm having a lot of trouble trying to modify a WD2500BEVT drive , manufacted the 29th of September , 2009 .
When I connect the HD to the pc and start the hddhackr command, the program says NO ATA IDENTIFY POSSIBLE , while when I start up Windows Xp (keeping the WD device connected) , during the system loading screen it locks.
Is the device broken ? Or it's the chipset's fault?

Please help me  :o
« Last Edit: November 05, 2009, 03:21:47 PM by Hatenko »

ponno

  • Newbie
  • *
  • Posts: 7
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #236 on: November 05, 2009, 10:15:04 PM »
HI,

need a bit of help. I ran HDDHACKR and everything went well except the xbox just sees the new 120 gb drive as a 20. I'm not sureif I missed something.

I also tried clearing the cache and formating the drive on the xbox but no change.

Any ideas?

the drive is a WD1200BEVT-22ZCT0
LBA: 234441648
manufacture date is 08/06/2009
« Last Edit: November 05, 2009, 10:29:30 PM by ponno »

mindseye1

  • Newbie
  • *
  • Posts: 1
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #237 on: November 05, 2009, 11:26:52 PM »
Ok I think I've got a strange problem. When I start HDDHACKR in auto-mode it shows me my drives and asks me to select which one I want to flash. But then it continues to scroll down the screen as if a button on the keyboard was being held down. The same thing with manual mode. I get to the point where it asks to confirm the flash, but then it just keeps on scrolling down. Anyone else run into this?

damox

  • Master Hacker
  • ****
  • Posts: 485
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #238 on: November 05, 2009, 11:29:46 PM »
need a bit of help. I ran HDDHACKR and everything went well except the xbox just sees the new 120 gb drive as a 20. I'm not sureif I missed something.

Did you use the 20gig hddss.bin lol ?

ponno

  • Newbie
  • *
  • Posts: 7
    • View Profile
Re: HDDHackr v1.22 Build 20091022
« Reply #239 on: November 05, 2009, 11:35:29 PM »
need a bit of help. I ran HDDHACKR and everything went well except the xbox just sees the new 120 gb drive as a 20. I'm not sureif I missed something.

Did you use the 20gig hddss.bin lol ?

edit nvm I found one. just curious tho, if I have to use a hddss.bin from a 120, which makes sense, why do I need to dump the sectors on the 20gb?
« Last Edit: November 06, 2009, 12:04:33 AM by ponno »